Ivisons Electric Fencing Offset Wire Ring Insulator 220mm
Short descriptionVery good for extending the distance to the fence post - Ivisons Offset Tape Insulator is designed to make conventional fences – e.g. wooden fences, barbed wire or wire fences – more secure for animals.
Availability: In stock
Very good for extending the distance to the fence post
Offset insulators are designed to make conventional fences – e.g. wooden fences, barbed wire or wire fences – more secure for animals. The offset insulators are screwed onto the front of the existing fence, and the live electric fence poly wire or wire is then positioned in the insulators. The newly created gap prevents animals from damaging the fence, which significantly increases animal safety. An additional useful feature is that they also protect electric fences from discharges. If the existing electric conductors run too close to the hedge or bush, long-shaft insulators can increase the distance between the two. In this way, discharges and short circuits are reduced – the electric fence remains secure.
Why do you need this product?
If you need to keep livestock contained, or wild animals and other intruders out of your garden, electric fencing may be a good option for you. Both humane and effective, electric fencing can be used to enclose a pasture or garden, and are simple to install and maintain.
Step 1: The very first thing you must do is measure the parameters of the garden.
It is important to plan to have a foot space between the edge of the garden and any plants that are close to the edge. You will use this measurement to determine how much electrical wire you will need and approximately how many metal posts you should get.
Step 2: Get enough fence posts.
Poly posts are a perfectly good option as they are flexible enough not to break under stress, yet stiff enough to resist side-strain. They are low cost, lightweight and durable enough to last many years. Ivisons galvanised posts are the easiest to set in the ground. They’re made out of hot-dipped galvanised metal, guaranteeing a long-lasting post.
Tip: Layout the posts around the perimeter of the garden. The posts should be spaced about three to five feet apart. Adjust to best fit your garden. Once the stakes are laid out, use the sledgehammer to drive the metal stakes into the ground.
Step 3: Choose the right material for your electric fence.
You can install electric fencing with electric fence tape, rope and wire. Ivisons open weave tape allows the air to pass through and reduce 'whipping', it is also highly visible, very strong, and won't rust. Rope is a very popular choice for fencing in horses or cattle. It's thicker than wire, therefore, more visible, so the animals are less likely to attempt to get through. Wire is suitable for livestock that doesn't move too quickly, such a sheep.
Step 4: Build your fence.
Feed the wire through the eyelets of your poly posts, or through the insulators if you’ve opted for a galvanised post, and mount these at the start and end of the fence. You can use reels for winding and unwinding the conducting material. They’re particularly useful for long fences, problematic terrain or for temporary and semi-permanent fencing systems.
Tip: To avoid any loss of current at the start and end of the fence, do not tie knots in your conducting material.
Step 5: Select an energiser.
To keep the electric fence powered, you’ll need an energiser that will keep electrical current powering the fence wires. Ivisons Solar energiser doesn’t need an electric outlet but they do require a certain amount of sunlight and tends to be more suitable for smaller fencing systems. Select a suitable location for setting up your energiser. This location should provide protection from wind and rain. Energisers must have access to an AC outlet.
Step 6: Put in grounding posts.
To install electric fencing, you need at least 1 grounding post that is 6 feet or longer. Place 1 grounding rod near the charger and use a post-hole digger/slammer to set the grounding post. Leave at least 2 inches of the post above the ground. When installing electric fencing, it's a good idea to set another grounding post 10 feet to 20 feet from the first post.
Step 7: Attach a lead.
The wire needs to extend from the ground terminal of the energiser to all the grounding posts. Secure the wire to the posts with a grounding clamp.